Grout is the part of a tiled floor or shower that nobody chooses to look at, until one day the tile is fine and the lines between it have gone gray, brown, or black. The good news is that most discolored grout is dirt rather than damage, and dirt can be dealt with. The bad news is that grout is porous, so how you clean it matters a lot more than how hard you scrub.
Why grout gets dirty so easily
Standard cement-based grout behaves a bit like a hard sponge. It is full of tiny pores that soak up water, soap residue, body oils, and whatever gets tracked across the floor. Tile itself is glazed and sheds most of that. Grout does not, so the lines hold on to it.
The cause of the discoloration depends on where the grout is:
- Kitchen and entry floors: mostly ground-in soil and cooking grease. The grout looks uniformly dingy or tan.
- Shower and tub surrounds: soap scum plus mildew. Dark spots, often near the bottom of the wall or in corners that stay damp.
- Bathroom floors: a mix of hair, dust, and moisture. Gray lines that get worse near the tub or toilet.
Knowing which kind you have helps you pick the right approach, because grease and mildew do not respond to the same thing.
Start with the gentlest method
Before reaching for anything strong, try the simple route. Sweep or vacuum first so you are not turning loose grit into a paste. Then:
- Mix a few drops of dish soap into warm water.
- Apply it along the grout lines and let it sit for 5 to 10 minutes.
- Scrub with a stiff nylon grout brush or an old toothbrush, working along the line rather than across it.
- Wipe up the loosened dirt with a damp cloth or mop, then rinse with clean water.
For lightly dirty floors, this alone often brings grout back a shade or two lighter. It also costs almost nothing and does not risk the tile.
Baking soda paste for stubborn spots
If soap and water leave a stain behind, make a thick paste of baking soda and a little water. Spread it into the grout, leave it for 10 to 15 minutes, and scrub with the brush. Baking soda is a mild abrasive, so it lifts surface staining without chewing up the grout the way a metal-bristle brush can.
A word on vinegar: it gets recommended everywhere, but acid can slowly etch cement grout and will damage some natural stone tile, such as marble or travertine. If you have stone, skip it. We go into this in more detail in our post on whether vinegar is safe to clean with, and our guide to cleaning tips by flooring type covers what different surfaces tolerate.
When you need something stronger
For black mildew in showers, or grout that has stayed dark after the steps above, an oxygen-based cleaner (sodium percarbonate, sold as powdered oxygen bleach) is a sensible next step. Mix it with hot water according to the label, apply it to the grout, and give it time to work. Often that means 15 to 30 minutes, which is the part people skip. Then scrub and rinse well.
Some ground rules, since this is where people get into trouble:
- Never mix chlorine bleach with ammonia or acidic cleaners. The fumes are dangerous. If you are not sure what is already on the surface, rinse thoroughly before trying anything new.
- Ventilate. Run the bathroom fan and crack a window.
- Test a small hidden spot first, especially with colored grout, which can lighten unevenly.
- Keep strong cleaners off natural stone unless the product says it is stone-safe.
What not to do
- Don’t use a wire brush or steel wool. It scratches tile glaze and roughens the grout, which then traps even more dirt.
- Don’t soak and leave it. Cleaner drying on the surface leaves its own film.
- Don’t skip the rinse. Leftover residue attracts new dirt, which is why some grout looks clean for a week and then darkens again.
Sealing: the step that keeps it clean
Unsealed cement grout keeps absorbing whatever lands on it. Once the grout is clean and fully dry (give it at least a day, longer in a humid bathroom), a penetrating grout sealer fills the pores so spills sit on top where you can wipe them away. Follow the product directions for application and cure time. Sealing is not permanent; many manufacturers suggest reapplying periodically, especially in showers and on busy kitchen floors. If water beads on the grout, the seal is still working. If it darkens and soaks in, it is time to redo it.
When cleaning won’t fix it
Sometimes grout is not dirty, it is worn. Signs include cracking, crumbling, missing chunks, or a gap between grout and tile. Those lines let water get underneath, and that is a repair job (regrouting or caulking), not a cleaning one. Likewise, caulk at the tub edge that has gone black all the way through usually needs replacing rather than scrubbing. It is better to know the difference early than to spend a weekend scrubbing something that cannot come clean.
Keeping grout from getting bad again
Most of the work is prevention, and it takes less time than a big scrub session:
- Squeegee or wipe down shower walls after use, and run the exhaust fan for a while afterward.
- Vacuum or sweep tile floors regularly so grit does not grind into the lines.
- Mop with a diluted, residue-free cleaner instead of heavy detergent that can leave a film.
- Wipe up spills, especially coffee, juice, and grease, before they soak in.
If you would rather hand it off
Grout work is slow, repetitive, and tough on knees, which is why it tends to get put off. If you have tile that has gotten past the point of a quick wipe-down, a deep cleaning visit is where detail work like this fits better than a routine one. Our post on deep cleaning vs. standard cleaning explains the difference. For reference, deep cleaning starts at $210 for a studio, $220 for a 1BR, and $270 for a 2BR, assuming one bathroom and under 1,000 square feet. Final pricing depends on bathrooms, square footage, and add-ons, and you can see the broader breakdown in our pricing guide.
We are a licensed and insured cleaning company serving Arlington, with Ashburn as a secondary area across Northern Virginia. Questions about what a visit would cover for your home? Call us at 571-350-0866.